Product Model : SET220-10A
Input: 85v-290v
Output:190-300VDC
Switch Mode Power Supply
Hot-swappable technology
Soft-switching technology
Plug and Play
N+1 redundancy
RS232, RS485, SNMP Communication
High efficiency
Email :[email protected]
110 Or 220v DC Rectifier System
Description
110 Or 220v DC Rectifier System Description
1. Power supply modules of series SET- 220V/110V are compact battery charging rectifiers with rear side connectivity. The rectifiers are designed for high voltage Power Plants and Substations. Due to the modular concept and a high scalability the user is able to equip the power supply with additional modules according to his actual power profile. The chargers are very user friendly and can be swapped as well as upgraded during system operation.
2. The devices get their operation parameters via the system RS 485 communication bus. After a successful login a central monitoring unit controls and monitors the devices. In case of interruption due to failure of monitoring unit the modules operate continuously with internal default values.Therefore the supply of the connected loads and the charging of the batteries are guaranteed without any interruption. Step less temperature control fan speed & change with the output power of module, which minimize noise & extend fan life.The rectifier needs a 1Ph AC mains connection.
3. Rectifier power circuit is divided into active PFC & DC to DC converter which can make the wide input voltage range (85V-290V) & high efficiency.High power density has reached the international advanced level.
110 Or 220v DC Rectifier System Features
1. LED indication for On / Fault status
2. Protection for Input and output over /under voltage, over temperature, and short circuit
3. “Hot plug-in” design with back plane connection
4. High power density, RS 485 Interface for Remote Adjusting, Controlling, Measuring and Signaling.
5. High Efficiency with low EMI. CE Safety and EMC certification
Input
| Type | 220V/10A | 110V/20A |
| Model No. | SET-220V/10A | SET-110V/20A |
| Input voltage | 85-290VAC (Nominal 180-290VAC) | |
| Input current | 13.6A | |
| Input frequency range | 45 Hz-65 Hz | |
| Power Factor | ≥ 0.99 at P nom ≥ 75% | |
Output
| Nominal output voltage (Vnom) | 220VDC | 110VDC |
| Adjustable output voltage range | 190-300VDC | 95-150VDC |
| Voltage Stabilization Accuracy | ± 0.5% | |
| Current Stabilization Accuracy | ± 1 % | |
| Nominal output current (Inom) | 10ADC@300VDC | 20A DC@150VDC |
| Efficiency | ≥ 95 % | |
| Charge characteristic line | IU Characteristic according to | |
| DIN41772/DIN41773 | ||
| Default value of the charging | 240V | 120V |
| voltage | ||
| O/p Overvoltage Vo> (factory | 302V | 151V |
| set) | ||
| Voltage ripple | ≤ 200 mV | |
| Dynamic accuracy of the | <3% of Venom at load change | |
| charging voltage | from 10% -90%-10% ;Transient | |
| time<50 ms | ||
| Short circuit protection | 15% – 30% of Inom when in short | |
| circuit | ||
| Parallel operation | Yes .Current Sharing ± 3% | |
110 Or 220v DC Rectifier System Mechanical
| Type | 220V/10A | 110V/20A |
| Model No. | SET-220V/10A | SET-110V/20A |
| Weight approx. | 2.4 kgs | |
| Dimensions (W/H/D) | 103x88x261 | |
| Type of enclosure / | IP 20 | |
| Protection class | ||
| Color (front panel) | Front Black | |
110 Or 220v DC Rectifier System Technial Data
| Communications interface | RS 485 |
| Ambient temperature | Operation: -20° to+55° C , |
| Storage:-40° to +70° C | |
| Humidity | ≤ 90 % RH |
| Cooling | Fan Cooled |
| Climatic conditions | IEC-68-2-2, IEC-68-2-3, IEC-68-2-6 |
| Max. Installation altitude | ≤2000 m |
| Audible noise | < 50 db |
| Connections | AC Input DC Output and Signalization at rear |
| CE conformity | Yes |
| Compliance to EMC standards | EN61000-4-2, EN-61000-4-6, EN-61000-4-3, EN-61000-4-12 |
| Air Pressure | 70-106 Pa |
| Insulation Resistance | Input Chassis & Output > 10M Ohms at 500VDC |
| Dielectric strength | 2000V between Input, Output & Chassis for 1Min. |
These power supplies are designed for a wide range of applications such as:
1. Power supply for all medium to high power DC loads
2. Telecommunication.
3. Rectifiers in DC systems with battery backup
4. Industrial control systems.
5. Charging and buffering of stationary batteries in electrical power plants
